55 lines
3.6 KiB
Markdown
55 lines
3.6 KiB
Markdown
## FPC BM-Lite example application
|
|
|
|
This is a port of [FPC BM-Lite Development Kit](https://www.fingerprints.com/solutions/access/bm-lite-development-kit/ "BM-Lite Development Kit") to Nordic nRF52840-DK development board. FPC BM-Lite module connected to the dev board by SPI interface.
|
|
|
|
There are 3 main folders in the project:
|
|
- [BMLite_example](BMLite_example) - main HW-independed application
|
|
- [hcp](hcp) - implementation of HCP protocol
|
|
- [HAL_Driver](HAL_Driver) - implementation of HW-dependent functions
|
|
|
|
------------
|
|
|
|
### Platform-independent interface functions
|
|
|
|
Platform-independent interface implemented in [platform.c](BMLite_example/src/platform.c)
|
|
|
|
| Platform function | Description |
|
|
| :-------- | :-------- |
|
|
| bool **platform_init**(uint32_t speed_hz) | Initilalizes hardware |
|
|
| void **platform_bmlite_reset**(void) | Implements BM-Lite HW Reset |
|
|
| fpc_com_result_t **platform_bmlite_send**(uint16_t size, const uint8_t *data, uint32_t timeout, void *session) | Send data packet to FPC BM-LIte (session parameter is for compatibility and can be safely ignored) |
|
|
| fpc_com_result_t **platform_bmlite_receive**(uint16_t size, uint8_t *data, uint32_t timeout, void *session) | Receive data packet from FPC BM-LIte (session parameter is for compatibility and can be safely ignored) |
|
|
|
|
Currently **platform_bmlite_send()** and **platform_bmlite_receive()** are implemented for SPI interface. For UART interface there is no need to wait **IRQ** pin ready. However because in UART mode there is no signal from FPC-BM-LIte that it will send data, I would recommend to use UART interrupt or DMA to receive data from UART and store it to a separate buffer and read data in **platform_bmlite_receive()** from that buffer. Activation UART data reading only inside **platform_bmlite_receive()** could lead to loosing some incoming data and causing HCP protocol errors.
|
|
|
|
------------
|
|
|
|
### HAL implementation
|
|
|
|
For porting the project to a new microcontroller, all functions from [bmlite_hal.h](BMLite_example/inc/bmlite_hal.h) should be implemented.
|
|
|
|
#### Functions must be implemented:
|
|
|
|
| HAL Function | Description |
|
|
| :------------ | :------------ |
|
|
| void **hal_board_init**(uint32_t speed_hz) | Initialize GPIO, System timer, SPI |
|
|
| void **hal_bmlite_reset**(bool state) | Activate/Deactivate BM-Lite **RST_N** pin (***Active Low***) |
|
|
| fpc_bep_result_t **hal_bmlite_spi_write_read**(uint8_t *write, uint8_t *read, size_t size, bool leave_cs_asserted) | SPI data exchange |
|
|
| bool **hal_bmlite_get_status**(void) | Return status of BM-Lite **IRQ** pin (***Active High***) |
|
|
| void **hal_timebase_init**(void) | Initialize system clock with 1 msec tick |
|
|
| uint32_t **hal_timebase_get_tick**(void) | Read currect system clock value |
|
|
| void **hal_timebase_busy_wait**(uint32_t ms) | Delay for **ms** msec |
|
|
|
|
#### Optional functions for implementing user interface in BM-Lite example application:
|
|
|
|
| HAL Function | Description |
|
|
| :------------ | :------------ |
|
|
| uint32_t **hal_get_button_press_time**(void) | How long UI button was pressed last time. Also it should reset button pressed time counter |
|
|
| void **hal_set_leds**(platform_led_status_t status, uint16_t mode) | Set LED(s) state according to status and mode. |
|
|
|
|
------------
|
|
|
|
### Some notes about FPC BM-Lite HW interface
|
|
|
|
- BM-Lite support both UART and SPI communication interface. BM-Lite automatically detects the specific communication interface in use. However, it is not possible to use both interfaces at the same time!
|
|
- **IRQ** pin is used in SPI mode only as FPC BM-Lite Ready-to-Transmit signal. The module set it to **High** when it has some data to send and set it to **Low** when data packet is sent. |